Auto support generated by Cura looks dubious but ok
Conversation
Nope. Support adhesion failed near end of print. I think I need a raft for this. And/or design in my own supports. The two pillars at horn tips got ripped up. Wonder why? Up-tension from horn curve?
1
On the plus side got to try my dremel for clean-up cutting off of supports and sanding.
1
1
Not the best job but am starting to get the hand of using a dremel. The high-rpm/low-pressure way is much more fun than a drill.
1
1
Recently remembered one of my earliest introductions to engineering thinking: my dad (a mechanical engineer) posing a classic CAD brainteaser to me when I was a teenager: what object looks like a circle in the top view, a triangle in the front view, and a square in the side view?
1
1
2
Later in freshman engineering school, our engineering drawing instructor posed the same brainteaser, before proceeding to demonstrate the answer by shaping a piece of chalk into the answer (whittling a piece of chalk by rubbing it on a board is legit machining btw)
1
5
The answer, which I just made in OnShape using the loft feature, is a thing which may have a name, I don't know, but is kinda like an oddly shaped cone frustum. Here is the drawing:
2
5
Ignore weird lines. They are an artifact of how OnShape does lofts geometrically. A loft is when you smoothly transform one face of an object into another. In this case, the 2nd surface should actually be a 1-d edge, but OnShape needs a face, so I made a very narrow rectangle.
1
Another way to pose the brainteaser is to ask: what object can plug a square, circular, or triangular hole, depending on how you orient it? So just for fun, I made a stencil of that too.
1
1
Stay tuned... 3d printing both rn, and will have a video presently.
1
I actually don't know if this is the "only" correct answer. Afaict, a 3-projection view completely determines a solid model, but maybe complex surfaces have indeterminacy. I think I'll have to sand off some edges to make it the right answer.
Replying to
Doh. Of course the solution is not unique. This one is skew symmetric. Any set of contours that fits within the 3 contours will do. I could have added a halfway loft plane with an ellipse cross section and that would have forced symmetry.
1
Anything contour that stays within the bounding box defined by square and triangle projection lines will work. Blue is what OnShape generated. Red is what I’d force if I wanted.
1
Also reprinting the horns from yesterday. Scaled down 50% with raft. Dunno what all that wispy stray fiber is. Too dry? From supports being printed coarse? PLA spool being not as good? Drip during travel?
1
Done. Messed up a bit tried to make the triangle equilateral and the rectangle a square at the same time. Doh. No way to satisfy this template. If you have a square, triangle will be isosceles.
1
1
3
The horns printed fine but that fuzz is a mess. Not sure it will clean up easy.
1
After some cleanup. Not much better.
1
1
Called on the brain trust for help.
Quote Tweet
3d printing mavens… any tips for sanding PLA prints down to a smooth finish? @divalbanerjee @h_thoreson @chenoehart
1
Much excite. Printing TPU for the first time. If it works I’ll be able to design my own tires 🥳😱
en.m.wikipedia.org/wiki/Thermopla
Just a simple rubbery washer to start with.
2
5
Fingers crossed. Seems to be printing fine. Shiny with some stringing. Used Cura generic presets for TPU-95, whatever that is. Higher nozzle temperature (228F) but lower bed temperature (45) than PLA (205/65)
2
Ok it’s ugly and messy and needs a haircut but it basically works.
1
4
ugh broke thread... continues here
Quote Tweet
Decent compliance, rather stiff at normal resolution printing with 60% infill. I bet I could get much wider range by messing with infill density. But clearly settings need work. But unlike PETG this feels different enough as a material, it’s worth mastering.
Show this thread
0:12
1.1K views
1
1
