Tweetovi

Blokirali ste korisnika/cu @svenpetersen191

Jeste li sigurni da želite vidjeti te tweetove? Time nećete deblokirati korisnika/cu @svenpetersen191

  1. Prikvačeni tweet

    And BTW, I am not sponsored by anybody. When I tweet about a product, it is my own opinion and I don't get paid for it. So, it cannot be advertisment.

    Poništi
  2. Meanwhile... real life temperature testing. After 2 1/2 hours, it is an acceptable value.

    Poništi
  3. I am constructing the case for the WiFi-Modem Rev. 2, which fit both versions o the NodeMCU, the 25.4mm wide and the 31mm wide. I am doing this from scratch, since the original was my first construction and I have learned a bit since then.

    Poništi
  4. I almost gave up. Trying to repair the vacuum cleaner thing. It could not be switched to hard floor mode anymore. A magnet got suck in the mechanism and looked like a regular part :-)))

    Poništi
  5. On the other hand, such an LED panel produces a nice light. Almost shadow free and soft. CRI 80 is not exactly great. That is an LED problem. But there are better LEDs.

    Prikaži ovu nit
    Poništi
  6. It is not visible without the camera. But the data sheet said „No flickering“. 👎🏿👎🏾👎🏽👎🏼👎🏻👎

    Prikaži ovu nit
    Poništi
  7. I have installed a new „flicker free“ LED light in the kitchen. Ok, I have checked it with the iPad camera. Not exactly flicker free, I would say. It is not a bad flicker, though.

    Poništi
  8. Now, I wrote some info on my replacement power supply:

    Poništi
  9. Poculator... that sounds like an instrument the doctor uses to hurt one badly. I am sure, it will hurt in the next morning in case you drink several.... you can probably catch flies with it, when you sprinkle it on the table. Sweet and heavy. Yuck :-))

    Poništi
  10. I have put my collection of C64 schematics (all pdf) on my website.

    Poništi
  11. Well, I should have done that some months ago. I will modify my Wifi Modem design, so the original WeMos and the wider copies of the NodeMCU will both fit one board. Just made the "combo" footprint.

    Poništi
  12. Poništi
  13. The perspective matters :-))))

    Prikaži ovu nit
    Poništi
  14. How to fake a half decent looking workbench picture for twitter :-)

    Prikaži ovu nit
    Poništi
  15. Maybe I can put it on my website. It is quite an improvement, but not perfect, though.

    Prikaži ovu nit
    Poništi
  16. Recommended reading and especially the video.

    Poništi
  17. Is there actually a schematic of ASSY 250466, that is more readable than this?

    Prikaži ovu nit
    Poništi
  18. Now, I am printing a top, that is 4mm higher and has even more ventilation holes (at the side). If it is radiation, the intensity will drop with the square of the radius. Other than that, at least the top needs to be printed with petg, which is not my favorite.

    Prikaži ovu nit
    Poništi
  19. Many new ventilation holes and there is still this temperature. Maybe, it is not hot air, but IR radiation. I have no clue, never delt with it.

    Prikaži ovu nit
    Poništi
  20. Poništi
  21. Some more ventilation slots: what about this?

    Prikaži ovu nit
    Poništi

Čini se da učitavanje traje već neko vrijeme.

Twitter je možda preopterećen ili ima kratkotrajnih poteškoća u radu. Pokušajte ponovno ili potražite dodatne informacije u odjeljku Status Twittera.

    Možda bi vam se svidjelo i ovo:

    ·