@bsmtiam

big glitch energy

Vrijeme pridruživanja: kolovoz 2012.
52 fotografije ili videozapisa Fotografije i videozapisi

Tweetovi

Blokirali ste korisnika/cu @bsmtiam

Jeste li sigurni da želite vidjeti te tweetove? Time nećete deblokirati korisnika/cu @bsmtiam

  1. 1. sij

    Soldered one up and it shows up on the debugger. Color me surprised.

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  2. 13. stu 2019.

    The beatstep saga continues! Made a STM32F1 LQFP100 target board for my ChipWhisperer. Pretty hastily done, but I think it could work.

    1 reply 4 korisnika označavaju da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  3. proslijedio/la je Tweet
    29. kol 2019.

    I am officially releasing my SM5 Assembler

    1 proslijeđeni tweet 5 korisnika označava da im se sviđa
    Poništi
  4. 26. srp 2019.

    Hi I'm basement and I like AT&T syntax.

    Poništi
  5. 8. srp 2019.

    Broke down and bought an original pitch control board off ebay for $70. It's finally back together! Now to get another phono preamp and make a mixer.

    1 reply 1 korisnik označava da mu se sviđa
    Poništi
  6. 4. tra 2019.

    Got off my ass and measured the resistance of the pitch slider at various points. Not exactly happy with the precision of the results as I had to eyeball everything. Probably going to try again with a laser tachometer and a better multimeter.

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  7. proslijedio/la je Tweet
    29. ožu 2019.

    why wont god let me die

    7.165 proslijeđenih tweetova 21.065 korisnika označava da im se sviđa
    Poništi
  8. 16. ožu 2019.

    RCA board fits first try, barely.

    1 reply 2 korisnika označavaju da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  9. 4. ožu 2019.

    : ' )

    1 korisnik označava da mu se sviđa
    Poništi
  10. 26. velj 2019.

    Oh cool, the bearings on the tonearm are fucked. Guess I'll redo its PCB too while I wait for parts. Drawing that outline in Kicad was not fun.

    1 reply 1 korisnik označava da mu se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  11. 23. velj 2019.

    I can design my own and get 3 of them made at OSHPark for $2.50 lawl. There's even a spot for an extra dimming resistor squeezed in. Designed in Australia.

    1 reply 1 korisnik označava da mu se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  12. 23. velj 2019.

    Pads are ripped off in a lot of places. This one just has the LEDs for the strobe. Replacements are $10 for just the PCB, closer to 20-30 with LEDs.

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  13. 22. velj 2019.

    Also started restoring the metalwork. After a good scrub with some degreaser and bit of polishing, it doesn't look bad. Much better than before at least.

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  14. 22. velj 2019.

    The Technics potentiometer also has a weird taper. There's a dip in the middle, which I presume is how they turn on the LED and lock the motor frequency to 0 when it's set to 0% pitch change. Looks like I'll have to figure out a circuit to emulate that. Or use an MCU.

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  15. 22. velj 2019.

    Just got the new Bourns sliding potentiometers in the mail. $5 each vs over $50 for the exact one used in the 1200MK2. The Bourns unit has no center detent, which most DJs remove anyways, and feels a little lighter than the OG Technics one.

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  16. 19. velj 2019.

    Sooooooooo let's design our own and save like $50.

    1 reply 1 korisnik označava da mu se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  17. 19. velj 2019.

    Oh and new pitch controls sell for over $100; usually around $60 for the fader and $30-40 for the PCB. That's ridiculous.

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  18. 19. velj 2019.

    Restoring a Technics 1200 turntable I found for cheap. The last person who worked on it should never be allowed near electronics ever.

    1 reply 3 korisnika označavaju da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  19. proslijedio/la je Tweet
    17. velj 2019.

    7 replies 346 proslijeđenih tweetova 1.012 korisnika označava da im se sviđa
    Poništi
  20. 10. velj 2019.

    SnOwMaGeDdOn

    1 reply 2 korisnika označavaju da im se sviđa
    Poništi

@bsmtiam još nije objavio nijedan Tweet.

Čini se da učitavanje traje već neko vrijeme.

Twitter je možda preopterećen ili ima kratkotrajnih poteškoća u radu. Pokušajte ponovno ili potražite dodatne informacije u odjeljku Status Twittera.

    Možda bi vam se svidjelo i ovo:

    ·