Aliz

@AlizTheHax0r

I do security stuff, also 'old computer' stuff. British, living in Singapore. Sorta trans, depending on your definition. Pronouns are anything, I don't mind.

Singapore
Vrijeme pridruživanja: listopad 2011.
439 fotografija ili videozapisa Fotografije i videozapisi

Tweetovi

Blokirali ste korisnika/cu @AlizTheHax0r

Jeste li sigurni da želite vidjeti te tweetove? Time nećete deblokirati korisnika/cu @AlizTheHax0r

  1. Prikvačeni tweet
    13. lip 2018.

    Oh, on gender pronouns - I don't mind any, but since I present male everyone always uses male. If you'd like to use female pronouns for me to balance it out a little, that'd make me happy! Minor preference though, anything's okay with me.

    1 proslijeđeni tweet 9 korisnika označava da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  2. proslijedio/la je Tweet
    prije 15 sati

    Anyone Wanna Hang Out and Just Name Stuff From the ’90s With Me?

    9 replies 91 proslijeđeni tweet 531 korisnik označava da mu se sviđa
    Poništi
  3. proslijedio/la je Tweet
    3. velj

    If Microsoft Teams is down for you... Remember it's Office *365* and there are 366 days in 2020.

    1.011 proslijeđenih tweetova 3.278 korisnika označava da im se sviđa
    Poništi
  4. proslijedio/la je Tweet
    2. velj

    Aluminum foil boat floating on sulfur hexafluoride gas.

    8 replies 135 proslijeđenih tweetova 590 korisnika označava da im se sviđa
    Poništi
  5. 2. velj

    Current status:

    Poništi
  6. proslijedio/la je Tweet
    2. velj

    hi guess who just found out about the fact that there's been a consistent choice to use binary typewriters in MLP and is currently losing her fucking mind over it

    12 proslijeđenih tweetova 67 korisnika označava da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  7. 2. velj

    New Bojack is On Point.

    1 korisnik označava da mu se sviđa
    Poništi
  8. 2. velj

    Apparently I was right the first time, ugh. Anyway I removed the ammeter, all the other non-essential stuff, and it's still playing up. Fuck it, time to buy a different controller. >_<

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  9. proslijedio/la je Tweet
    2. velj

    Hey wanna come to Hawaii with me and collect squid for science this June? Well... that’s a thing you can totally do. In fact, I’d REALLY recommend it because it’s wicked fun.

    166 proslijeđenih tweetova 1.084 korisnika označavaju da im se sviđa
    Poništi
  10. 2. velj

    Also, fuck, I just realised I wired the ammeter's shunt resistor (0.5ohm IIRC?) on the 0v side of the PSU, so all the 0v lines are effectively a couple volts higher depending on load. That won't be helping my noise issues. :$

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  11. proslijedio/la je Tweet
    2. velj

    Remember when Kermit the Frog made a cameo appearance in The Little Mermaid?

    61 reply 640 proslijeđenih tweetova 4.230 korisnika označava da im se sviđa
    Poništi
  12. proslijedio/la je Tweet
    1. velj

    I don't know what to say about this:

    21 reply 8 proslijeđenih tweetova 107 korisnika označava da im se sviđa
    Poništi
  13. 1. velj

    Fucking ground issues

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  14. 1. velj

    "that's weird, why do the ground pins on the tinyg not show conductivity, I thought they were connected, better check th- OH"

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  15. 1. velj

    NO KIDDING

    Odgovor korisnicima @gsuberland @LargeCardinal
    lmao
    Poništi
  16. proslijedio/la je Tweet
    31. sij

    I always thought paying a contractor to create a PCB footprint for a part you want to use was a waste of money, but then I saw this.

    14 replies 15 proslijeđenih tweetova 98 korisnika označava da im se sviđa
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  17. 1. velj

    holy shit

    It's life, Jim, but not as we know it.
    Prikaži ovu nit
    1 korisnik označava da mu se sviđa
    Poništi
  18. 1. velj

    Urgh I'm having no end of problems with this goddamn board (tinygv6). I'm really tempted to replace it, either with a modern tinyg or something else. Anyone got any recommendations?

    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  19. 1. velj

    Had to use an external programmer to rescue it, ugh. Now I get to see if I have a recent backup of the config or not, since it lost all its settings.. hope I don't have a day of tuning acceleration jerk rates ahead of me >_<

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  20. 1. velj

    GDI, every time I go to CNC something there's a new problem that stops me! Today's is that the controller wouldn't come out of bootloader mode. Apparently with my super-old tinyg v7 the atmega chip's fuses were set with incorrect brownout levels.. >_<

    1 reply
    Prikaži ovu nit
    Prikaži ovu nit
    Poništi
  21. proslijedio/la je Tweet
    31. sij

    This reddit thread/comments about not using your home address on ride sharing apps is... brutal

    6 proslijeđenih tweetova 11 korisnika označava da im se sviđa
    Poništi

@AlizTheHax0r još nije objavio nijedan Tweet.

Čini se da učitavanje traje već neko vrijeme.

Twitter je možda preopterećen ili ima kratkotrajnih poteškoća u radu. Pokušajte ponovno ili potražite dodatne informacije u odjeljku Status Twittera.

    Možda bi vam se svidjelo i ovo:

    ·